- r -

• RACEFLIGHT_IDENTIFIER : msp_protocol.h
• RAD_TO_DEG : definitions.h
• RADDRESS : RCOutput_AeroIO.cpp
• RadiansToCentiDegrees : definitions.h
• RADIUS_OF_EARTH : definitions.h
• RALLY_INCLUDE_HOME_DEFAULT : AP_Rally.cpp
• RALLY_LIMIT_KM_DEFAULT : AP_Rally.cpp
• RAMEND : Scheduler.h
• RAMTRON_RDID : AP_RAMTRON.cpp
• RAMTRON_RDSR : AP_RAMTRON.cpp
• RAMTRON_READ : AP_RAMTRON.cpp
• RAMTRON_WREN : AP_RAMTRON.cpp
• RAMTRON_WRITE : AP_RAMTRON.cpp
• RANGE_2000DPS : AP_InertialSensor_RST.cpp
• RANGE_250DPS : AP_InertialSensor_RST.cpp
• RANGE_500DPS : AP_InertialSensor_RST.cpp
• RANGEFINDER_GROUND_CLEARANCE_CM_DEFAULT : RangeFinder.h
• RANGEFINDER_MAX_INSTANCES : RangeFinder.h
• RANGEFINDER_PREARM_ALT_MAX_CM : RangeFinder.h
• RANGEFINDER_PREARM_REQUIRED_CHANGE_CM : RangeFinder.h
• RATE_1000HZ_LP_780HZ : AP_InertialSensor_RST.cpp
• RATE_100HZ_LP_25HZ : AP_InertialSensor_RST.cpp
• RATE_100HZ_LP_74HZ : AP_InertialSensor_RST.cpp
• RATE_200HZ_LP_25HZ : AP_InertialSensor_RST.cpp
• RATE_200HZ_LP_50HZ : AP_InertialSensor_RST.cpp
• RATE_200HZ_LP_70HZ : AP_InertialSensor_RST.cpp
• RATE_400HZ_LP_100HZ : AP_InertialSensor_RST.cpp
• RATE_400HZ_LP_20HZ : AP_InertialSensor_RST.cpp
• RATE_400HZ_LP_25HZ : AP_InertialSensor_RST.cpp
• RATE_400HZ_LP_292HZ : AP_InertialSensor_RST.cpp
• RATE_400HZ_LP_50HZ : AP_InertialSensor_RST.cpp
• RATE_50HZ_LP_37HZ : AP_InertialSensor_RST.cpp
• RATE_800HZ_LP_100HZ : AP_InertialSensor_RST.cpp
• RATE_800HZ_LP_30HZ : AP_InertialSensor_RST.cpp
• RATE_800HZ_LP_35HZ : AP_InertialSensor_RST.cpp
• RATE_800HZ_LP_50HZ : AP_InertialSensor_RST.cpp
• RATE_DOP : AP_GPS_UBLOX.h
• RATE_HW : AP_GPS_UBLOX.h
• RATE_HW2 : AP_GPS_UBLOX.h
• RATE_POSLLH : AP_GPS_UBLOX.h
• RATE_PVT : AP_GPS_UBLOX.h
• RATE_SOL : AP_GPS_UBLOX.h
• RATE_STATUS : AP_GPS_UBLOX.h
• RATE_VELNED : AP_GPS_UBLOX.h
• rc_ch : AP_Mount_Backend.cpp
• RC_CHANNEL_TYPE_ANGLE : RC_Channel.h
• RC_CHANNEL_TYPE_RANGE : RC_Channel.h
• RC_DEAD_TIME : RCInput.h
• RC_INPUT_MAX_CHANNELS : RCInput.h
• RC_INPUT_MAX_PULSEWIDTH : RCInput.h
• RC_INPUT_MIN_PULSEWIDTH : RCInput.h
• RC_NEUTRAL : Config.h
• RC_OUTPUT_MAX_PULSEWIDTH : RCOutput.h
• RC_OUTPUT_MIN_PULSEWIDTH : RCOutput.h
• RC_SPEED : RC_UART.cpp
• RCIN_PRUSS_RAM_BASE : RCInput_AioPRU.h
• RCIN_PRUSS_SHAREDRAM_BASE : RCInput_PRU.cpp
• RCIN_RPI_BUFFER_LENGTH : RCInput_RPI.cpp
• RCIN_RPI_CLK_LEN : RCInput_RPI.cpp
• RCIN_RPI_DMA_CHANNEL : RCInput_RPI.cpp
• RCIN_RPI_DMA_CONBLK_AD : RCInput_RPI.cpp
• RCIN_RPI_DMA_CS : RCInput_RPI.cpp
• RCIN_RPI_DMA_D_DREQ : RCInput_RPI.cpp
• RCIN_RPI_DMA_DEBUG : RCInput_RPI.cpp
• RCIN_RPI_DMA_DEST_INC : RCInput_RPI.cpp
• RCIN_RPI_DMA_END : RCInput_RPI.cpp
• RCIN_RPI_DMA_INT : RCInput_RPI.cpp
• RCIN_RPI_DMA_LEN : RCInput_RPI.cpp
• RCIN_RPI_DMA_NO_WIDE_BURSTS : RCInput_RPI.cpp
• RCIN_RPI_DMA_PER_MAP : RCInput_RPI.cpp
• RCIN_RPI_DMA_RESET : RCInput_RPI.cpp
• RCIN_RPI_DMA_SRC_INC : RCInput_RPI.cpp
• RCIN_RPI_DMA_WAIT_RESP : RCInput_RPI.cpp
• RCIN_RPI_GPIO_LEV0_ADDR : RCInput_RPI.cpp
• RCIN_RPI_MAX_COUNTER : RCInput_RPI.cpp
• RCIN_RPI_MAX_SIZE_LINE : RCInput_RPI.cpp
• RCIN_RPI_PCM_CS_A : RCInput_RPI.cpp
• RCIN_RPI_PCM_DREQ_A : RCInput_RPI.cpp
• RCIN_RPI_PCM_FIFO_A : RCInput_RPI.cpp
• RCIN_RPI_PCM_GRAY : RCInput_RPI.cpp
• RCIN_RPI_PCM_INT_STC_A : RCInput_RPI.cpp
• RCIN_RPI_PCM_INTEN_A : RCInput_RPI.cpp
• RCIN_RPI_PCM_LEN : RCInput_RPI.cpp
• RCIN_RPI_PCM_MODE_A : RCInput_RPI.cpp
• RCIN_RPI_PCM_RXC_A : RCInput_RPI.cpp
• RCIN_RPI_PCM_TXC_A : RCInput_RPI.cpp
• RCIN_RPI_PCMCLK_CNTL : RCInput_RPI.cpp
• RCIN_RPI_PCMCLK_DIV : RCInput_RPI.cpp
• RCIN_RPI_RPI1_CLK_BASE : RCInput_RPI.cpp
• RCIN_RPI_RPI1_DMA_BASE : RCInput_RPI.cpp
• RCIN_RPI_RPI1_PCM_BASE : RCInput_RPI.cpp
• RCIN_RPI_RPI2_CLK_BASE : RCInput_RPI.cpp
• RCIN_RPI_RPI2_DMA_BASE : RCInput_RPI.cpp
• RCIN_RPI_RPI2_PCM_BASE : RCInput_RPI.cpp
• RCIN_RPI_SAMPLE_FREQ : RCInput_RPI.cpp
• RCIN_RPI_TIMER_BASE : RCInput_RPI.cpp
• RCIN_SYSFS_PATH : RCInput_Navio2.cpp
• RCIN_ZYNQ_PULSE_INPUT_BASE : RCInput_ZYNQ.cpp
• RCINPUT_UDP_DEF_PORT : RCInput_UDP.h
• RCINPUT_UDP_NUM_CHANNELS : RCInput_UDP_Protocol.h
• RCINPUT_UDP_VERSION : RCInput_UDP_Protocol.h
• RCOU_SERIAL_TIMING_DEBUG : RCOutput.cpp
• RCOUT_BEBOP_RTPRIO : RCOutput_Bebop.cpp
• RCOUT_DEBUG_LATENCY : RCOutput.cpp
• RCOUT_PRUSS_CTRL_BASE : RCOutput_AioPRU.h
• RCOUT_PRUSS_IRAM_BASE : RCOutput_AioPRU.h
• RCOUT_PRUSS_RAM_BASE : RCOutput_AioPRU.h
• RCOUT_PRUSS_SHAREDRAM_BASE : RCOutput_PRU.h
• RCOUT_ZYNQ_PWM_BASE : RCOutput_ZYNQ.cpp
• RDDEM : ff.c
• READ_PREFIX : RCOutput_AeroIO.cpp
• RED_PWM_INDEX : DiscoLED.cpp
• REFERENCE_G : AP_InertialSensor_LSM9DS0.cpp
• REFERENCE_X : AP_InertialSensor_LSM9DS0.cpp
• REFERENCE_Y : AP_InertialSensor_LSM9DS0.cpp
• REFERENCE_Z : AP_InertialSensor_LSM9DS0.cpp
• REG1_BDU_UPDATE : AP_Compass_LSM303D.cpp
• REG1_POWERDOWN_A : AP_Compass_LSM303D.cpp
• REG1_RATE_100HZ_A : AP_Compass_LSM303D.cpp
• REG1_RATE_12_5HZ_A : AP_Compass_LSM303D.cpp
• REG1_RATE_1600HZ_A : AP_Compass_LSM303D.cpp
• REG1_RATE_200HZ_A : AP_Compass_LSM303D.cpp
• REG1_RATE_25HZ_A : AP_Compass_LSM303D.cpp
• REG1_RATE_3_125HZ_A : AP_Compass_LSM303D.cpp
• REG1_RATE_400HZ_A : AP_Compass_LSM303D.cpp
• REG1_RATE_50HZ_A : AP_Compass_LSM303D.cpp
• REG1_RATE_6_25HZ_A : AP_Compass_LSM303D.cpp
• REG1_RATE_800HZ_A : AP_Compass_LSM303D.cpp
• REG1_RATE_BITS_A : AP_Compass_LSM303D.cpp
• REG1_X_ENABLE_A : AP_Compass_LSM303D.cpp
• REG1_Y_ENABLE_A : AP_Compass_LSM303D.cpp
• REG1_Z_ENABLE_A : AP_Compass_LSM303D.cpp
• REG2_AA_FILTER_BW_194HZ_A : AP_Compass_LSM303D.cpp
• REG2_AA_FILTER_BW_362HZ_A : AP_Compass_LSM303D.cpp
• REG2_AA_FILTER_BW_50HZ_A : AP_Compass_LSM303D.cpp
• REG2_AA_FILTER_BW_773HZ_A : AP_Compass_LSM303D.cpp
• REG2_ANTIALIAS_FILTER_BW_BITS_A : AP_Compass_LSM303D.cpp
• REG2_FULL_SCALE_16G_A : AP_Compass_LSM303D.cpp
• REG2_FULL_SCALE_2G_A : AP_Compass_LSM303D.cpp
• REG2_FULL_SCALE_4G_A : AP_Compass_LSM303D.cpp
• REG2_FULL_SCALE_6G_A : AP_Compass_LSM303D.cpp
• REG2_FULL_SCALE_8G_A : AP_Compass_LSM303D.cpp
• REG2_FULL_SCALE_BITS_A : AP_Compass_LSM303D.cpp
• REG5_ENABLE_T : AP_Compass_LSM303D.cpp
• REG5_RATE_100HZ_M : AP_Compass_LSM303D.cpp
• REG5_RATE_12_5HZ_M : AP_Compass_LSM303D.cpp
• REG5_RATE_25HZ_M : AP_Compass_LSM303D.cpp
• REG5_RATE_3_125HZ_M : AP_Compass_LSM303D.cpp
• REG5_RATE_50HZ_M : AP_Compass_LSM303D.cpp
• REG5_RATE_6_25HZ_M : AP_Compass_LSM303D.cpp
• REG5_RATE_BITS_M : AP_Compass_LSM303D.cpp
• REG5_RATE_DO_NOT_USE_M : AP_Compass_LSM303D.cpp
• REG5_RES_HIGH_M : AP_Compass_LSM303D.cpp
• REG5_RES_LOW_M : AP_Compass_LSM303D.cpp
• REG6_FULL_SCALE_12GA_M : AP_Compass_LSM303D.cpp
• REG6_FULL_SCALE_2GA_M : AP_Compass_LSM303D.cpp
• REG6_FULL_SCALE_4GA_M : AP_Compass_LSM303D.cpp
• REG6_FULL_SCALE_8GA_M : AP_Compass_LSM303D.cpp
• REG6_FULL_SCALE_BITS_M : AP_Compass_LSM303D.cpp
• REG7_CONT_MODE_M : AP_Compass_LSM303D.cpp
• REG_ADC_READ : AP_Airspeed_MS5525.cpp
• REG_CNTL1 : AP_Compass_AK09916.cpp
• REG_CNTL2 : AP_Compass_AK09916.cpp
• REG_CNTL3 : AP_Compass_AK09916.cpp
• REG_COMPANY_ID : AP_Compass_AK09916.cpp
• REG_CONTROL0 : AP_Compass_MMC3416.cpp
• REG_CONTROL0_NB : AP_Compass_MMC3416.cpp
• REG_CONTROL0_REFILL : AP_Compass_MMC3416.cpp
• REG_CONTROL0_RESET : AP_Compass_MMC3416.cpp
• REG_CONTROL0_SET : AP_Compass_MMC3416.cpp
• REG_CONTROL0_TM : AP_Compass_MMC3416.cpp
• REG_CONTROL1 : AP_Compass_MMC3416.cpp
• REG_CONVERT_D1_OSR_1024 : AP_Airspeed_MS5525.cpp
• REG_CONVERT_D1_OSR_2048 : AP_Airspeed_MS5525.cpp
• REG_CONVERT_D1_OSR_256 : AP_Airspeed_MS5525.cpp
• REG_CONVERT_D1_OSR_4096 : AP_Airspeed_MS5525.cpp
• REG_CONVERT_D1_OSR_512 : AP_Airspeed_MS5525.cpp
• REG_CONVERT_D2_OSR_1024 : AP_Airspeed_MS5525.cpp
• REG_CONVERT_D2_OSR_2048 : AP_Airspeed_MS5525.cpp
• REG_CONVERT_D2_OSR_256 : AP_Airspeed_MS5525.cpp
• REG_CONVERT_D2_OSR_4096 : AP_Airspeed_MS5525.cpp
• REG_CONVERT_D2_OSR_512 : AP_Airspeed_MS5525.cpp
• REG_CONVERT_PRESSURE : AP_Airspeed_MS5525.cpp
• REG_CONVERT_TEMPERATURE : AP_Airspeed_MS5525.cpp
• REG_DEVICE_ID : AP_Compass_AK09916.cpp
• REG_HXH : AP_Compass_AK09916.cpp
• REG_HXL : AP_Compass_AK09916.cpp
• REG_HYH : AP_Compass_AK09916.cpp
• REG_HYL : AP_Compass_AK09916.cpp
• REG_HZH : AP_Compass_AK09916.cpp
• REG_HZL : AP_Compass_AK09916.cpp
• REG_ICM_INT_PIN_CFG : AP_Compass_AK09916.cpp
• REG_ICM_PWR_MGMT_1 : AP_Compass_AK09916.cpp
• REG_ICM_WHOAMI : AP_Compass_AK09916.cpp
• REG_ID : AP_Baro_LPS2XH.cpp
• REG_PRODUCT_ID : AP_Compass_MMC3416.cpp
• REG_PROM_BASE : AP_Airspeed_MS5525.cpp
• REG_RESET : AP_Airspeed_MS5525.cpp
• REG_ST1 : AP_Compass_AK09916.cpp
• REG_ST2 : AP_Compass_AK09916.cpp
• REG_STATUS : AP_Compass_MMC3416.cpp
• REG_TMPS : AP_Compass_AK09916.cpp
• REG_TO_FLOAT : px4io_protocol.h
• REG_TO_SIGNED : px4io_protocol.h
• REG_XOUT_L : AP_Compass_MMC3416.cpp
• RELAY1_PIN_DEFAULT : AP_Relay.cpp
• RELAY2_PIN_DEFAULT : AP_Relay.cpp
• RELAY3_PIN_DEFAULT : AP_Relay.cpp
• RELAY4_PIN_DEFAULT : AP_Relay.cpp
• REMOTE_LOG_DEBUGGING : DataFlash_MAVLink.cpp
• REPETITIONS_XY_REG : AP_Compass_BMM150.cpp
• REPETITIONS_Z_REG : AP_Compass_BMM150.cpp
• REQUIRE : AP_Test.h
• RESET_AND_MISC_CONTROL : CameraSensor_Mt9v117.cpp
• RESET_RPA2_WAIT_MS : AP_Proximity_RPLidarA2.cpp
• RESET_SOC_I2C : CameraSensor_Mt9v117.cpp
• RestartBootloader : blheli_4way_protocol.h
• RESYNC_TIMEOUT : AP_Proximity_RPLidarA2.cpp
• RGB_LED_HIGH : AP_Notify.h
• RGB_LED_LOW : AP_Notify.h
• RGB_LED_MEDIUM : AP_Notify.h
• RGB_LED_OFF : AP_Notify.h
• RNFD_BEBOP_DEFAULT_ADC_FREQ : AP_RangeFinder_Bebop.h
• RNFD_BEBOP_DEFAULT_FREQ : AP_RangeFinder_Bebop.h
• RNFD_BEBOP_FILTER_POWER : AP_RangeFinder_Bebop.h
• RNFD_BEBOP_MAX_ECHOES : AP_RangeFinder_Bebop.h
• RNFD_BEBOP_NB_PULSES_MAX : AP_RangeFinder_Bebop.h
• RNFD_BEBOP_NB_PULSES_PURGE : AP_RangeFinder_Bebop.h
• RNFD_BEBOP_SOUND_SPEED : AP_RangeFinder_Bebop.h
• RNFD_BEBOP_TRANSITION_COUNT : AP_RangeFinder_Bebop.h
• RNFD_BEBOP_TRANSITION_HIGH_TO_LOW : AP_RangeFinder_Bebop.h
• RNFD_BEBOP_TRANSITION_LOW_TO_HIGH : AP_RangeFinder_Bebop.h
• ROUTING_DEBUG : MAVLink_routing.cpp
• ROW : Display.h
• RP_DEBUG_LEVEL : AP_Proximity_RPLidarA2.cpp
• RPI_GPIO_10 : GPIO_RPI.h
• RPI_GPIO_11 : GPIO_RPI.h
• RPI_GPIO_12 : GPIO_RPI.h
• RPI_GPIO_13 : GPIO_RPI.h
• RPI_GPIO_14 : GPIO_RPI.h
• RPI_GPIO_15 : GPIO_RPI.h
• RPI_GPIO_16 : GPIO_RPI.h
• RPI_GPIO_17 : GPIO_RPI.h
• RPI_GPIO_18 : GPIO_RPI.h
• RPI_GPIO_19 : GPIO_RPI.h
• RPI_GPIO_2 : GPIO_RPI.h
• RPI_GPIO_20 : GPIO_RPI.h
• RPI_GPIO_21 : GPIO_RPI.h
• RPI_GPIO_22 : GPIO_RPI.h
• RPI_GPIO_23 : GPIO_RPI.h
• RPI_GPIO_24 : GPIO_RPI.h
• RPI_GPIO_25 : GPIO_RPI.h
• RPI_GPIO_26 : GPIO_RPI.h
• RPI_GPIO_27 : GPIO_RPI.h
• RPI_GPIO_28 : GPIO_RPI.h
• RPI_GPIO_29 : GPIO_RPI.h
• RPI_GPIO_3 : GPIO_RPI.h
• RPI_GPIO_30 : GPIO_RPI.h
• RPI_GPIO_31 : GPIO_RPI.h
• RPI_GPIO_4 : GPIO_RPI.h
• RPI_GPIO_5 : GPIO_RPI.h
• RPI_GPIO_6 : GPIO_RPI.h
• RPI_GPIO_7 : GPIO_RPI.h
• RPI_GPIO_8 : GPIO_RPI.h
• RPI_GPIO_9 : GPIO_RPI.h
• RPLIDAR_CMD_EXPRESS_SCAN : AP_Proximity_RPLidarA2.cpp
• RPLIDAR_CMD_FORCE_SCAN : AP_Proximity_RPLidarA2.cpp
• RPLIDAR_CMD_GET_DEVICE_HEALTH : AP_Proximity_RPLidarA2.cpp
• RPLIDAR_CMD_GET_DEVICE_INFO : AP_Proximity_RPLidarA2.cpp
• RPLIDAR_CMD_RESET : AP_Proximity_RPLidarA2.cpp
• RPLIDAR_CMD_SCAN : AP_Proximity_RPLidarA2.cpp
• RPLIDAR_CMD_STOP : AP_Proximity_RPLidarA2.cpp
• RPLIDAR_PREAMBLE : AP_Proximity_RPLidarA2.cpp
• RPM_MAX_INSTANCES : AP_RPM.h
• RTC_CONSOLE_REG : boards.h
• RTC_DSM_BIND_REG : boards.h
• RTC_MASS_STORAGE_REG : boards.h
• RTC_OV_GUARD_REG : boards.h
• RTC_OVERCLOCK_REG : boards.h
• RTC_SIGNATURE_REG : boards.h
• RX_BOUNCE_BUFSIZE : UARTDriver.h
• RX_ERROR_MASK : AP_GPS_SBF.cpp
• RX_FIFO_FS_SIZE : usb_conf.h